by Nick Di Cristofaro

chainclean

Using a chain-cleaning tool is the most effective way to get all the grease and crud off

Whether you have a state-of-the-art racing machine or a journeyman ride, you need to keep your whip clean. Not only will you keep it looking good, but you’ll ensure it’s performing well, so you can, too.

RELATED: 10 things to check before you ride your new bike

Floss the cassette with a rag to get it sweaky clean

Floss the cassette with a rag to get it sweaky clean

Removing the crud throughout the drivetrain will not only have everything running at its best, but it also and cassette, you can still get them pretty clean leaving them installed. Spray the cassette with degreaser and scrub with a hard-bristle brush to loosen up the crud. Next, “floss” in between each cog with a thin rag,and then spray one more time and blow dry. You may need to repeat this process a few times. With the chain, you can leave the rear wheel on the bike or remove the wheel and use a chain-tension device. Grab your chain-cleaning tool and place it on the chain. Rotate the cranks a few times. Remove the tool and dry the chain with rags and air. Spray the derailleurs with degreaser and use the brush to scrub. Pay attention to the jockey wheels on the rear derailleur. Gunk usually accumulates there.

RELATED: 5 easy steps to make your components last longer

Spray the derailleur with degreaser before scrubbing it with a brush

Spray the derailleur with degreaser before scrubbing it with a brush

Pay close attention to get the jockey wheels clean so they run smooth

Pay close attention to get the jockey wheels clean so they run smooth

With the drivetrain done, you can move on to the rest of the bike with or without water. Use a low pressure garden hose to spray down the bike. I stress the word “low.” You do not need a high-powered pressure washer. Using one will force water into the crank and headset bearings. A pressure washer can also damage frame finishes. Even with a garden hose, try to stay away from the bottom bracket, headset and hubs. Use a brush to scrub the wheels and tires and a sponge to go over the bike. Rinse and repeat if you see a spot you missed. Avoid soaking the bar tape as it might take long to dry out, especially in colder temperatures.

RELATED: Dust off your ride with this easy 8-step spring tune-up

Wipe off the rims

Wipe off the rims

Clean the frame to make it shine

Clean the frame to make it shine

If you opt for the no-water option, diluted Simple Green cleaner and a clean microfibre cloth work well. You can also use a toothbrush in and around the brake area, but stay away from using excess soap on discbrake rotors and calipers.

RELATED: Drivetrain care: Keep your ride as smooth as the day you bought your bike

Finally lubricate the chain and derailleur pivots

Finally lubricate the chain and derailleur pivots

The final step is to install the wheels and lubricate the chain and derailleur pivot points. Do not forget this step. You should use a clean rag and brake cleaner or degreaser to give brake rotors or braking tracks a wipe. The finishing touch would be to detail the frame and wheels (minus the braking surfaces) with a polish and microfibre cloth while keeping polish away from braking areas. Once your bike is clean, take a moment to admire your work before getting out to ride.

RELATED: Winter Cleaning – Show your bike some TLC

Top tools for cleaning your bike

Essentials
– Warm soapy water in a bucket
– A couple of old toothbrushes, sponge and brush
– A garden hose
– Diluted Simple Green cleaner or equivalent in a spray bottle
– Chain-tension device, so you can turn the cranks and chain with the rear wheel removed
– Clean rags, microfibre cloth and polish/detailer

Nice to have
– Bike stand
– Chain-cleaning device with degreaser
– Air compressor


Related

3 Comments

  • RHP says:

    Something I do is use an old hub, from a wheel that had a rim wear out, as a “placeholder” for the rear hub. I even have an old cassette on this hub, and use it to “tension” the chain while cleaning it. This way I can leave the chain to dry independent of the cogs while I clean them separately.
    I know, not everyone can do this, but if you ever get your hands on a spare, old, hub…

  • Dan Kitching says:

    Shimano Pro and Pedro’s both have quick release axles to do that job for very little money. The Shimano one has a single cog that is brilliant.

    • Dan Kitching says:

      Actually, just realized it’s the Shimano Pro item being used this article’s photos LOL!
      This is a tool EVERYONE should have

1 Trackback

Leave a Reply